heys guys im new here, i was looking for some 468 builds. i want 10.1 comp, 550hp and just as much torque...or close. its gonna be a street engine. what parts or who has the best kit to start this build? any input will really help me out thanks!!!
Printable View
heys guys im new here, i was looking for some 468 builds. i want 10.1 comp, 550hp and just as much torque...or close. its gonna be a street engine. what parts or who has the best kit to start this build? any input will really help me out thanks!!!
Doug Herbert performance parts has a lot of kits for any engine you would like and pritty good prices I might add. There web site dosent have the rotating assemblies listed but there magizine has lots of kits. I am just geting into big blocks but from what I have seen It is not that hard to build a 550hp torque monster. Jegs I pritty good to.
Summit Racing.com or you can go to Sparks Nv and pick out what you want.
I have been searching high and low the last few months,and everything i come across is 7,10 thousand dollar range.I found this one at summit with all NEW forged parts for 5700.BBC 502.
http://store.summitracing.com/partde...5&autoview=sku
here are a few links
http://www.competitionproducts.com/
http://dynoflow.substorm.com/short_b...ragrace421.asp
http://racingjunk.com/
http://www.adperformance.com/
PC wont let post any more links,hmmm.
i can put you a kit to gether or sell you a done engine and beat or match them and have built many big block chevys . so if you need some info on them . will them some phone jockey help you much? I can build you any thing in a big block chevy or sell you any thing for one if you need
i just need some build specs and parts list, i was think of going with some edelbrock heads, a 830 holley, some hedman 2x3 headers,a forged crank, and i was thinkin of putting in either some H rods, arp bolts everwhere, . i need help with the cam and the pistons. im looking for 10.1 comp. so do any of you guys have any previous builds simular? or any that will get these power results?
yes i have but you do not need the h beam rods .stock rods with arp will work up to that. and you will need big tube headers and on the cam i would run a roller soild or hyd. if buying a steel crank why not go up to a 496 and you will easly get you 550 hpwith 10 to1 cr i use srp pistons
hmmmm maybe. what cam would you recomend?
this would have alot to do with rpm you want to run it to .and if you will drive it at low speed alot street car? or more of a drag car
well its for a street engine. i thinkin of redlining this engine at 6k rpm, so probally middle rpm, like anywhere from 3k rpm on.. if that helps any. i want power not too low but not to high , so in the middle.
3000to6500 heavy car ?roller cam hyd howards part 120255 600/570 288/294@0.50 230/236 112 or something close to it
PAT sounds like you'v done this a time or to,Hay MAGEMAN good choice on the Aluminum Heads you will loose a lot of weight staying away from the cast heads.I would go with the BRODIX Heads instead of EDELBROCK but thats just my preferance.I went to BBL longgggggg time ago wont tell all my secrets but will tell you get the RECTANGLE-PORTS not the OVAL-PORTS..By the way pat good advice to MAGEMAN.
all i do is big block chevys and have done them for many years i have done other engines and can make them run but .big block are some thing i like . have not used one i did not like all from 396 to 632
well pat what do you think i should put in this engine?.... :)
i need alot of help with the heads.
well i do not know what you are asking ?the cam i put down would be a good cam mild street /strip but i do not know you .there are some hard core guys running bigger cams than that and i have put some in but below 3000 rpm s you may not like them big cams on low speed driving . on the heads you tell me how much you what to spend and if you are looking for iron or alum. O ports can do a very good job and a low rpm engine will work better with them. for hi mild to top end the rec ports but port size cc are really what you asking? if you go big ports they will not work good at low rpms
Megaman like PAT said don't go to big on the cam,my Monte mite and i do mean mite see some slite street usage,I run a LUNATI Pro street cam 3500 rpm range with 4.10 gear.CAM LIFT:615int/620ext DURATION 362int/365ext pistons cut heads milled,.045thick head gasket,double valve springs,long slot rocker arms.(ETC)the problem I ran in to is my power Brakes no longer worked .the big cams don't make enough vacume to run brake BOOSTER.and do not work to well with vacum secondary carbs.now I have to switch to a differant master-cylinder (IE) non power brakes.
eek. well for the heads im willing to fork out a few grand, and aluminum, so im not limited too much as for the cost. ill have to run that cam or one similar and see how i like it first. okay i want to build the 468 mentioned in chevy hi performance. the ''ROAST RAT'' check that out and let me know and what you would recomend. i was planning on running a few different parts, like the carb and different exhaust. but thats what im going for.
MEGAMAN,what site do I find this "ROAST-RAT" ?
chevyhiperformance.com, its in the tech forums under engine builds and on the 7 spicy combos page. check it out .
i did see the build but do not think the cam i told you i would run is that far off. if the build they did you like. then build this one. why ask? if you are looking for a build that as been done for more power then that one?here is the way i see this. they have more money and parts they can get there hands on for them dyno runs. the small guy don't have the time or parts. i have built many big block and not every one get on the dyno. this cost time and money if you build it the way they did there is no way for sure you will get them numers more or less. i do not spend much time with a guy that come in my shop with a hot rod book in his hands. they are looking for something to get done and they do not know how to do it. but want you to tell them what is better then what they just pick up on the stand ?for the prices of the book ? that is to say if i had the killer engine com and i told every one what it was. how would i make a living ? i do not sell books and i have no companies paying me to use there parts .so at this point i may to you sound like a smart ass ? but i can only tell you what i think. but if you are checking me with someone else build then build that?
hey man i just wanted your input thats all. because i wanted to change some stuff thats all . im not A SMART ASS. kick back man i was just checking in because it sounds like youve been doing this a while thats all.
:whacked: read the post i said i did not want you to think i was a smart ass at is point i guess it dos not matter:confused:
oh my bad man, hahaha sorry! i totally dont think that at all. sorry for the misconception.
well the way i see this if your go up on the cam you will need more cr and if you go to a bigger cam you will need bigger heads if want to make big hp.and will have take it where the cam make power and at this point you will be making HP not Tq so at 2500 rpms the car will not make any hp and not much tq so you have to be carefull not to go to big on the port size of the head or the cam if the cr is low