On the cheap.

Hi guys. I have been doing some checking around to find some parts at a resonable price to build my tall deck.(525) I am having a hard time finding everything and keeping it below $5,000. I know that Is not a lot of money for a good build up but it is looking like that will be the limit. Even with the cheapest parts I could find though perfomance companys,Jegs,Summit,Doug Herbert, and Ohio Crank I cant get it below $5,500 and I dont know what machine work will cost yet. Is the 525 possible on $5,000 or will I need more cash.:confused: :HMMM:

Big blocks cost considerably more than a small block. Jegs does gaurentee lowest prices, so whatever you get from them company's, is the cheapest it's gonna be.

If I go with a steel bottom end rather than a forged to save money will the steel hold up to 600 horse or so. I would like to have at least 550 but I want 600 or more.

Ok I think I can do it if I get my crank and rods from Ohio Crank. Why are they so cheap. The 4340 4.50 inch crank is only $625, and the 4340 I beam rods are $200. I dont want junk so if anybody has heard of this or used this company let me know how they are. Also are these heads about the right size. Merlin lll rec.310cc.

i did one two years ago for 6500 srp pistons ohio rods scat 4130 crank new gm tall deck block hyd roller cam crane builder roller rockers edelbrock heads milodon pan moroso windage tray tci rattler air gap intake and still made money on the build jegs dose not have the best deals look at competitionproducts.com . or save up and send it or stop by joe with your money and stuff and pickup a done engine that will run:)

Quote:

---

Originally posted by joe bogger
Ok I think I can do it if I get my crank and rods from Ohio Crank. Why are they so cheap. The 4340 4.50 inch crank is only $625, and the 4340 I beam rods are $200. I dont want junk so if anybody has heard of this or used this company let me know how they are. Also are these heads about the right size. Merlin lll rec.310cc.

---

the head are ok but you may want to go to the h beams if you are going to really hammer it .i have use a lot of there stuff it works good they have a new i beam billet rod that is nice to i have used over 20 +sets of there h beam rods never had any thing go bad from there rods

Quote:

---

Originally posted by pat mccarthy
i did one two years ago for 6500 srp pistons ohio rods scat 4130 crank new gm tall deck block hyd roller cam crane builder roller rockers edelbrock heads milodon pan moroso windage tray tci rattler air gap intake and still made money on the build jegs dose not have the best deals look at competitionproducts.com . or save up and send it or stop by joe with your money and stuff and pickup a done engine that will run:)

---

Jegs may not have the best deals, but they gaurentee it, so you could prove to them there not the cheapest on any product that they sell and another company has cheaper, and they have to at least match the price, might be a hassle, but they might also drop the price below the other company's price, so they get the order. Summit has way better prices on most stuff, but sombody with a lot of time could get stuff a little cheaper by doing stuff like that.:)

You can do the same thing at Wal Mart, if you find somthing cheaper.

some things you can not get cheaper then jegs oil pans intakes stuff like that. but jegs dose not give me dealer on any thing . if you buy a lot of parts. i go were the deals are. it adds up on a big build

Thanks guys and pat I will be stopping buy. I know I have said that a few times now but I will get there. I am dealing with my graduation open house stuff right know. Thanks again.

Im with Pat on this one. Jegs typically in their catalogs are more expensive #1.
Far as Summit and Jegs both go Im talking on the phone with techs that really dont care about anything other than selling you the part as fast as possible.

Now Competition products on the other hands IMO has more people who not just work in the performance industry but most of them indulge in the hobby as well. They are a smaller company, they take time to talk with you on the phone to help you get the correct product. When I was looking at Canfield heads the guy discussing heads spent at least 20 minutes on the phone giving me an education. Far as prices go, for the most part I think they beat Summit and jegs on most things.

So unlike Pat who is looking for volume discount...from a guy who just builds a motor every couple of years Competition products I believe is best

check Speedomotive.com

Hey guys I was thinking that it would save a bunch if I took the heads I have and have them ported. But was told not to wast my time bucause the truck heads a "peanut ports" are they a waste.

for a 526 yes you will not save any thing .new guilds ex seats hp valve job bigger valves 2.300 and 1.88 cut the heads. in the long run it will cost you more

I found a 540 with all new forged parts for $4099.Let me know if you would like the info.

Quote:

---

Originally Posted by BigTruckDriver

I found a 540 with all new forged parts for $4099.Let me know if you would like the info.

---

how much do you get for that? you can not buy the block for less than 1950 . last time i check this is not a long block? and at this point if so he will still need heads so ? and if you are taking just a short block i think i can beat that how many do you want ? i would be happy to build any big block chevy and shipp it any were the usa :)

ok thats out. Thanks for the offer on the 540 but if it is a short block I can do my 525 short block way cheaper and maybe end up with more torge because it is a longer stroke. Thanks anyway.

yes joe you will have less money in your block. take that money and buy a set of good heads i may have some world or dart iron heads used that are nice at a fair price e may me if so

What size of heads are they. And what kind of engine where they on. Like a blown beast fed buy NOS.

Quote:

---

Originally Posted by joe bogger

What size of heads are they. And what kind of engine where they on. Like a blown beast fed buy NOS.

---

no blown up junk if that is what you are getting at .they may have been on blown big blocks it is hard to say what size of engines .i just have the heads

Do you know what size heads they are.

345 and 320 cc intake runners

Are the 345's to big for my engine. And do ether one have any special port or chamber work done.

how hi will you run it ? you can build the engine to them heads 345. BUT it will make more hp but will need more rpm the heads i have some work .bowl work and chambers. the smaller port heads may work better for lower rpms with no blower your engine builder will go over this with you

Well for one thing if I come down and see you, and like what I see you may be my machinest. If you do that, of which I thought I read where you said you did. And I wanted to run a hydraulic roller so where ever that would put me then I geuss those heads would do. I dont realy have a rpm limit its just where ever the cam puts me and my budget. I dont realy have a set limit on a budget ether but I dont want to put 10,000 into my first high horespower big block at 18 years old.

well i do look at my gallery them are all engine. i built . i build engines and machine work.but i am very busy at this time of year so if you want me to do this you will have to make appointment and get a hold of me .this time of year i have customer that race. i have a lot of happy customers so you should get a hold of me if you want .if you are serious

I am serious and I understand you being so busy. All the machine shops around here are. I just never know what will happen with the money situation. But I am getting there. It may take me longer but that is because I have bills like everyone else but not alot of credit because I am 18. So on these heads. What kind of $$$ are we talking. I would love to have them but I am sure I dont have the cash. But thats why there's banks right. LOL.

Well I looked at your gallery and there is some impresive stuff in there. Keep up the good work and I'll try to get an appointment to come check stuff out but in the mean time I want to get an exact idea on what parts I want.

if you want the heads i will get you a price .i will not post the price . get to me by the end of this week or the first the may ok joe?

alright I didint think you would post it but it was worth a try. Talk to ya latter. I think I still got the number you gave me. Thanks.